Print

Megasquirt 3 Kits


Display per page
Sort by

This MS330-K_BL kit includes everything you will need to build your MegaSquirt-3. The genuine B&G partial kit with PCB3.0, the Bill Of Materials, the case, pre-machined endplates and heatsink bar, even the tube of heatsink compound and a bit of jumper wire is included. All you add is tools, solder, and time! The MS3X Xpander board is sold separately and allows you to fully take advantage of the MegaSquirt-3, including 8cyl sequential injection, 8 ignition outputs allowing 8cyl coil on plug, nitrous control, and more. Only other thing you might need is a tuning cable. We have those available as well for a few bucks.

MS330-K Kit Bill Of Materials (BOM) Includes:

  • MS3 Daughter Card
  • All 'Basic Components'
  • PWM Flyback Damping Circuit components
  • Hall Sensor/Coil(-) and VR Sensor Ignition Trigger Components
  • Current Limiting Circuit Components


 
The MS3 daughter card on its own will give you all these features and more:

  • VE and ignition tables are now both 16 x 16
  • 0.1% steps on VE table, 0.1 degree steps on ignition table
  • Socket for an onboard SD card - no laptop required for data logging  (SD Card not included)
  • Built in USB port
  • GM stepper IAC control
  • Closed loop idle and mixture control
  • CANBus communications for interface with GPIO Board, IO Extender, or other devices
  • Staged injection
  • Native support for many different OEM trigger patterns


The MS3 also gives you a starting point for even more expansion. You will be able to connect the headers on this board to additional hardware, such as the MS3X board to enable features like these:

  • 8 channel sequential fuel control
  • 8 channel sequential ignition control
  • Individual fuel and spark trim for cylinder by cylinder tuning
  • 2 and 3 channel PWM IAC control
  • 2 stage nitrous controller
  • Table switching for multi-fuel engines
  • 2 step launch control
  • And more!


For complete MS3 documentation, see ms3efi.com.

569.95
Delivery weight: 710 g

Stocklevel: 2

Put this little circuit board in your MegaSquirt-III to unlock its full potential! This board installs in the MS3 case with no soldering; just connect it with the included ribbon cables.

Install the MS3X board to add this whole list of inputs and outputs to the MS3 ECU:

  • 8 Sequential fuel injection outputs. Each can drive a high impedance injector, and unused injection outputs can be put to other purposes.
  • 8 Logic level 5 volt ignition outputs. Works with many types of ignition modules and coils, including LSx coils. Requires external module or coils with internal ignitors.
  • 6 Medium current outputs. Use for 2 stage progressive nitrous, boost control, tach output, 3 wire idle speed control, general purpose PWM or relay control, or many other potential applications.
  • 3 Analog inputs. Use for an external MAP sensor, second O2 sensor, fuel pressure, accelerometer, or general data logging.
  • 4 Switch inputs. Can be used to start data logging, arm a nitrous system, switch tables, launch control, VSS input (with external conditioner), and more.
  • 1 Cam sensor input. Can be used with VR, Hall, or optical sensors.

The MS3X has all these circuits on it, just ready for you to wire up and use them. No mod kits, no setting up custom special order ECUs, just plug in and enable it in TunerStudio. The MS3X is intended for use with the MS3 daughter card only.

144.95
Delivery weight: 120 g

Stocklevel: 2

This add on board solders on top of the MS3 daughter board and gives you two channels of knock input that the MS3 can use to retard spark. Using this module will give you a much more sophisticated knock detection circuit than on any previous MegaSquirt knock detection. Features include a programmable bandpass filter, levels that change with RPM, the ability to assign different cylinders to different sensors, and different gain levels for each cylinder. See the MS3 manual for details.

94.95

Not in stock: 60 day delivery period