Afdrukken

Megasquirt 3 Compleet


Weergave per pagina
Sorteren op

It's finally here! The MegaSquirt-III is a drop in daughter card that greatly expands the MegaSquirt's functionality.

We now have complete, ready to run MegaSquirt-III ECUs. This is the basic, batch fire version, but can be expanded to add sequential injection and 8 channel ignition control with an MS3X board. As it is, you'll gain a lot more processing power, speed, and features over the existing MS1 and MS2 systems even without the MS3X.

The MS3 daughter card on its own will give you all these features and more:
VE and ignition tables are now both 16 x 16
0.1% steps on VE table, 0.1 degree steps on ignition table
Socket for an onboard SD card - no laptop required for data logging  (SD Card not included)
Built in USB port
GM stepper IAC control
Closed loop idle and mixture control
CANBus communications for interface with GPIO Board, IO Extender, or other devices
Staged injection
Native support for many different OEM trigger patterns

The MS3 also gives you a starting point for even more expansion. You will be able to connect the headers on this board to additional hardware, such as the MS3X board to enable features like these:
8 channels sequential fuel control
8 channel sequential ignition control
Individual fuel and spark trim for cylinder by cylinder tuning
2 and 3 channel PWM IAC control
2 stage nitrous controller
Table switching for multi-fuel engines
2 step launch control

For complete MS3 documentation, see ms3efi.com.
And more!
 

769,95

Niet op voorraad: dagen levertijd

Zet deze kleine printplaat in uw MegaSquirt - III om zijn volledige potentieel te ontsluiten ! Dit bord wordt geïnstalleerd in de MS3 kast zonder solderen , gewoon aansluiten met de meegeleverde lint kabels.

Installeer het MS3X bord om deze hele lijst van in-en uitgangen toe te voegen aan de MS3 ECU :    

  • 8 sequentiële brandstofinjectie uitgangen. Ieder kan een hoge impedantie injector aansturen en ongebruikte injectie uitgangen kunnen voor andere doeleinden worden ingezet .    
  • 8 Logic level 5 volt ontsteking uitgangen. Werkt met vele soorten van ontsteking modules en bobines, waaronder lsx bobines.    Vereist externe module of spoelen met interne ontstekers .    
  • 6 Medium huidige uitgangen. Bruikbaar voor 2 fase progressieve nitrous, boost control, toerenteller uitgang, 3-draads stationair toerental regeling, algemene doeleinden PWM of relais controle of vele andere mogelijke toepassingen .    
  • 3 analoge ingangen . Gebruik voor een externe MAP-sensor , tweede O2 sensor , brandstofdruk , accelerometer , of algemene data logging .
  • 4 Schakel ingangen . Kan gebruikt worden om data logging beginnen , arm een nitrous systeem , schakelen tussen tabelen , launch control , VSS -ingang ( met externe conditioner ) en nog veel meer .    
  • 1 Cam sensor ingang . Kan gebruikt worden met VR , Hall of optische sensoren .

Op de MS3X zitten deze circuits al , gewoon bedraden en te gebruiken . Geen mod kits, zonder het instellen van aangepaste speciale bestelde ECU , gewoon inpluggen en instellen met TunerStudio . De MS3X is bedoeld voor gebruik met de MS3 dochterkaart .

144,95
Aflevergewicht: 120 g

Voorraadniveau: 2

Complete, ready to run MegaSquirt-III ECU with the MS3X expansion board. 2.5 bar MAP sensor is standard equipment.

The MS3 daughter card on its own will give you all these features and more:

  • VE and ignition tables are both 16 x 16 with full interpolation.
  • 0.1% steps on VE table, 0.1 degree steps on ignition table
  • Socket for an onboard SD card – no laptop required for data logging  (SD Card not included)
  • Built in USB port
  • GM stepper IAC control
  • Closed loop idle and mixture control
  • CANBus communications for interface with GPIO Board, IO Extender, or other devices
  • Staged injection
  • Native support for many different OEM trigger patterns

This MS3 EMS already has the MS3X expansion board installed, enabling the following features:

  • 8 Sequential fuel injection outputs. Each can drive a high impedance injector, and unused injection outputs can be put to other purposes.
  • 8 Logic level 5 volt ignition outputs. Works with many types of ignition modules and coils, including LSx coils and our IGN-1As. Requires external module or coils with internal ignitors.
  • 6 Medium current outputs. Use for 2 stage progressive nitrous, boost control, tach output, 3 wire idle speed control, general purpose PWM or relay control, or many other potential applications.
  • 3 Analog inputs. Use for an external MAP sensor, second O2 sensor, fuel pressure, accelerometer, or general data logging.
  • 4 Switch inputs. Can be used to start data logging, arm a nitrous system, switch tables, launch control, VSS input (Hall sensor or VR with external conditioner), and more.
  • 1 Cam sensor input. Can be used with VR, Hall, or optical sensors.

The MS3X has all these circuits on it, just ready for you to wire up and use them. No mod kits, no setting up custom special order ECUs, just plug in and enable it in TunerStudio.

For complete MS3 documentation and more see http://www.msextra.com/

895,95

Niet op voorraad: dagen levertijd

Dit add-on board soldeer bovenop de MS3 dochter board en geeft je twee kanalen van knock input, die de MS3 kan gebruiken om ontsteking te vertragen. Gebruik van deze module zal je een veel meer geavanceerde klop detectie circuit geven dan eerdere MegaSquirt klop detectie. Functies omvatten een programmeerbaar banddoorlaatfilter, niveaus die veranderen met de RPM, de mogelijkheid om verschillende cilinders toewijzen aan verschillende sensoren en verschillende gain niveaus voor elke cilinder. Zie de MS3 handleiding voor meer informatie.

94,95

Niet op voorraad: 60 dagen levertijd

72,95

Voorraadniveau: 1