Print

Megasquirt 3 Complete


Display per page
Sort by

It's finally here! The MegaSquirt-III is a drop in daughter card that greatly expands the MegaSquirt's functionality.

We now have complete, ready to run MegaSquirt-III ECUs. This is the basic, batch fire version, but can be expanded to add sequential injection and 8 channel ignition control with an MS3X board. As it is, you'll gain a lot more processing power, speed, and features over the existing MS1 and MS2 systems even without the MS3X.

The MS3 daughter card on its own will give you all these features and more:
VE and ignition tables are now both 16 x 16
0.1% steps on VE table, 0.1 degree steps on ignition table
Socket for an onboard SD card - no laptop required for data logging  (SD Card not included)
Built in USB port
GM stepper IAC control
Closed loop idle and mixture control
CANBus communications for interface with GPIO Board, IO Extender, or other devices
Staged injection
Native support for many different OEM trigger patterns

The MS3 also gives you a starting point for even more expansion. You will be able to connect the headers on this board to additional hardware, such as the MS3X board to enable features like these:
8 channels sequential fuel control
8 channel sequential ignition control
Individual fuel and spark trim for cylinder by cylinder tuning
2 and 3 channel PWM IAC control
2 stage nitrous controller
Table switching for multi-fuel engines
2 step launch control

For complete MS3 documentation, see ms3efi.com.
And more!

769.95

Not in stock: day delivery period

Put this little circuit board in your MegaSquirt-III to unlock its full potential! This board installs in the MS3 case with no soldering; just connect it with the included ribbon cables.

Install the MS3X board to add this whole list of inputs and outputs to the MS3 ECU:

  • 8 Sequential fuel injection outputs. Each can drive a high impedance injector, and unused injection outputs can be put to other purposes.
  • 8 Logic level 5 volt ignition outputs. Works with many types of ignition modules and coils, including LSx coils. Requires external module or coils with internal ignitors.
  • 6 Medium current outputs. Use for 2 stage progressive nitrous, boost control, tach output, 3 wire idle speed control, general purpose PWM or relay control, or many other potential applications.
  • 3 Analog inputs. Use for an external MAP sensor, second O2 sensor, fuel pressure, accelerometer, or general data logging.
  • 4 Switch inputs. Can be used to start data logging, arm a nitrous system, switch tables, launch control, VSS input (with external conditioner), and more.
  • 1 Cam sensor input. Can be used with VR, Hall, or optical sensors.

The MS3X has all these circuits on it, just ready for you to wire up and use them. No mod kits, no setting up custom special order ECUs, just plug in and enable it in TunerStudio. The MS3X is intended for use with the MS3 daughter card only.

144.95
Delivery weight: 120 g

Stocklevel: 2

Complete, ready to run MegaSquirt-III ECU with the MS3X expansion board. 2.5 bar MAP sensor is standard equipment.

The MS3 daughter card on its own will give you all these features and more:

  • VE and ignition tables are both 16 x 16 with full interpolation.
  • 0.1% steps on VE table, 0.1 degree steps on ignition table
  • Socket for an onboard SD card – no laptop required for data logging  (SD Card not included)
  • Built in USB port
  • GM stepper IAC control
  • Closed loop idle and mixture control
  • CANBus communications for interface with GPIO Board, IO Extender, or other devices
  • Staged injection
  • Native support for many different OEM trigger patterns

This MS3 EMS already has the MS3X expansion board installed, enabling the following features:

  • 8 Sequential fuel injection outputs. Each can drive a high impedance injector, and unused injection outputs can be put to other purposes.
  • 8 Logic level 5 volt ignition outputs. Works with many types of ignition modules and coils, including LSx coils and our IGN-1As. Requires external module or coils with internal ignitors.
  • 6 Medium current outputs. Use for 2 stage progressive nitrous, boost control, tach output, 3 wire idle speed control, general purpose PWM or relay control, or many other potential applications.
  • 3 Analog inputs. Use for an external MAP sensor, second O2 sensor, fuel pressure, accelerometer, or general data logging.
  • 4 Switch inputs. Can be used to start data logging, arm a nitrous system, switch tables, launch control, VSS input (Hall sensor or VR with external conditioner), and more.
  • 1 Cam sensor input. Can be used with VR, Hall, or optical sensors.

The MS3X has all these circuits on it, just ready for you to wire up and use them. No mod kits, no setting up custom special order ECUs, just plug in and enable it in TunerStudio.

For complete MS3 documentation and more see http://www.msextra.com/

895.95

Not in stock: day delivery period

This add on board solders on top of the MS3 daughter board and gives you two channels of knock input that the MS3 can use to retard spark. Using this module will give you a much more sophisticated knock detection circuit than on any previous MegaSquirt knock detection. Features include a programmable bandpass filter, levels that change with RPM, the ability to assign different cylinders to different sensors, and different gain levels for each cylinder. See the MS3 manual for details.

94.95

Not in stock: 60 day delivery period

72.95

Stocklevel: 1